To use a Plasson compression fitting correctly, cut the polyethylene pipe squarely and clean any burrs from the end. Ensure the internal components are properly seated, then push the pipe straight through the nut and split ring past the captive O-ring until it firmly hits the internal mechanical stop. Finally, tighten the cap nut securely by hand or with a proper wrench to lock the grip ring in place.
Choosing between a Sharkbite (push-to-connect) fitting and a traditional brass compression fitting depends on accessibility, permanence, and pipe material.
In plumbing infrastructure and building drainage schematics, SWR stands for Soil, Waste, and Rainwater.
In plumbing and pipe fitting terminology, MPT stands for Male Pipe Thread (featuring external threads designed to screw into a matching component), while FPT stands for Female Pipe Thread (featuring internal threads designed to accept a male-threaded...
High-Density Polyethylene (HDPE) pipes are typically joined using mechanical compression fittings (for smaller metric or rural diameters up to 160mm), butt fusion welding (melting pipe ends together with heat plates), electrofusion fittings (which fe...
A -6 AN fitting (Army-Navy standard) refers to a specialized high-performance fluid line connector featuring a 3/8-inch nominal tube size (computed as 6 sixteenths of an inch).
Plasson products are primarily engineered and manufactured at the company's main corporate headquarters and manufacturing facilities located in Israel (at Maagan Michael).
An incoming residential water pressure of 80 PSI is generally considered the maximum safe upper limit for standard household plumbing systems.
An "olive"—more commonly referred to in North America as a ferrule—is a small, ring-shaped metallic or plastic component used inside compression fittings.
NPS stands for National Standard Straight (in mechanical threads) or more commonly Nominal Pipe Size (in North American industrial pipe sizing standards).
Plasson fittings are world-renowned, high-quality mechanical compression fittings designed specifically for joining polyethylene (PE) pipes.
In plumbing schematics, product catalogs, and valve specifications, SWT stands for Sweat (sometimes referred to as Solder).
PN-10 (Pressure Nominal 10) is a standardized pressure rating designation indicating that a pipe, valve, or fitting is engineered to safely withstand a maximum working water pressure of 10 bar (approximately 145 PSI or 1 megapascal) at standard ambie...
The colored stripes running longitudinally along the exterior of polyethylene (poly) pipes serve as an standardized visual coding system to indicate the pipe's intended application and pressure rating.
No, you do not flare the copper or metal tubing when using a standard compression fitting.
The most common plumbing and industrial pipe fittings include elbows (used to change flow direction), tees (for splitting or combining fluid streams), couplings (to connect two straight pipes together), reducers (for transitioning between different p...
No, you typically do not need Teflon (PTFE) tape on the compression joint itself, because the seal is formed entirely by the metal-on-metal or metal-on-pipe compression of the olive against the tubing.
FIP stands for Female Iron Pipe (also frequently associated with Female Pipe Thread or FPT).
In general pipeline and plumbing configurations, the four most common foundational categories of fittings are couplings (used to join two straight pipes together), elbows (designed to change the direction of flow), tees (configured to branch flow off...
Plasson metric compression fittings are manufactured in a comprehensive range of diameters typically spanning from 16mm up to 125mm or 160mm depending on the specific product line.
The pressure rating (PSI) a fitting can hold depends entirely on its material composition, size, manufacturing standard, and connection type.
Plasson compression fittings are constructed using high-grade engineering thermoplastics. Their bodies and nuts consist of tough polypropylene copolymer enhanced with carbon black for UV stabilization.
Yes, it is entirely possible to overtighten a compression fitting, which can cause severe damage.
Plasson is a globally recognized, industry-leading manufacturing brand specializing in high-performance mechanical compression fittings, valves, and piping systems designed primarily for polyethylene (PE) pipes.
Professional plumbers typically assemble standard brass compression fittings clean and dry, relying entirely on the mechanical metal-on-metal compression of the ferrule (olive) against the pipe and fitting body to form a watertight seal.
In North American plumbing standards, CTS stands for Copper Tube Size. It represents a specific sizing convention where the outer diameter (OD) of the pipe is consistently 1/8-inch larger than the nominal size descriptor.